Zero out given ISSI page

Initialize latency module Call before adding resources

Resource Lookup resource: index of resource return: Name of resource

Looks up the trigger list for the given scan code (from the active layer) NOTE: Calling function must handle the NULL pointer case

Setup layers

Layer active at top of the stack

Rotation state update Queues up a rotation trigger event States: 0x00 - Off 0x01 - Activate 0x02 - On 0x03 - Deactivate

Shows a TriggerEvent

\brief Clear Pending Interrupt The function clears the pending bit of an external interrupt. \param [in] IRQn External interrupt numb

USB Input buffer available

USB Get Character from input buffer

Output Module Data Periodic

Update and prepare for sleep mode There is no undo for this, the MCU must be reinitialized

USB RawIO buffer available

USB RawIO get buffer

Soft Chip Reset

Sends a mouse command over the USB Output buffer XXX This function *will* be changing in the future If you use it, be prepared that your .kll files wi

SWDIO I/O pin: Switch to Input mode (used in SWD mode only). Configure the SWDIO DAP hardware I/O pin to input mode. This function is called prior \re

SWDIO/TMS I/O pin: Set Output to Low. Set the SWDIO/TMS DAP hardware I/O pin to low level. */

SWDIO/TMS I/O pin: Set Output to High. Set the SWDIO/TMS DAP hardware I/O pin to high level. */

Disable JTAG/SWD I/O Pins. Disables the DAP Hardware I/O pins which configures: - SWCLK, SWDIO, nRESET to High-Z mode. */

Setup SWD I/O pins: SWCLK, SWDIO, and nRESET. Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode: - SWCLK, SWDIO, nRESET to output

Process the animation stack element - Returns 1 if the animation should be re-added to the stack - Returns 0 if the animation is finished (clean-up me

Pixel Frame Interpolation Tweening Do averaging between key frames

Standard Pixel Frame Function (no additional processing)

Basic interpolation Pixel Pixel Function TODO - Only works with Colummn and Row fill currently

Standard Pixel Pixel Function (standard lookup, no additonal processing)

Debug info for PixelElement

Iterate over each element in the Animation Stack If the animation is complete, do not re-add to the stack - The stack is re-built each time. - Ignores

Sets the device into firmware reload mode

Soft Chip Reset

Reads Unique Id into sam_UniqueId buffer

Read user signature

Evaluate/Update ResultMacro

Process delayed capabilities Capabilities that are not called immediately (i.e. ones that are not deemed as thread safe) are processed with this funct

* * SEGGER_RTT_Init * * Function description * Initializes the RTT Control Block. * Should be used in RAM targets, at start of the applic

* * SEGGER_RTT_Read * * Function description * Reads characters from SEGGER real-time-terminal control block * which have been previously

* * SEGGER_RTT_Write * * Function description * Stores a specified number of characters in SEGGER RTT * control block which is then read

* * SEGGER_RTT_WriteNoLock * * Function description * Stores a specified number of characters in SEGGER RTT * control block which is then

* * SEGGER_RTT_WriteString * * Function description * Stores string in SEGGER RTT control block. * This data is read by the host. * * Pa

* * SEGGER_SYSVIEW_GetSysDesc() * * Function description * Triggers a send of the system information and description. * */

* * SEGGER_SYSVIEW_Init() * * Function description * Initializes the SYSVIEW module. * Must be called before SystemViewer attaches t

* * SEGGER_SYSVIEW_OnIdle() * * Function description * Record an Idle event. */

* * SEGGER_SYSVIEW_RecordExitISR() * * Function description * Format and send an ISR exit event. * * Additional information * For

* * SEGGER_SYSVIEW_RecordU32() * * Function description * Formats and sends a SystemView packet containing a single U32 * parameter

* * SEGGER_SYSVIEW_RecordU32x2() * * Function description * Formats and sends a SystemView packet containing 2 U32 parameter payload. *

* * SEGGER_SYSVIEW_SetRAMBase() * * Function description * Sets the RAM base address, which is subtracted from IDs in order * to sa

* * SEGGER_SYSVIEW_Start() * * Function description * Start recording SystemView events. * This function is triggered by the host ap

* * SEGGER_SYSVIEW_Stop() * * Function description * Stop recording SystemView events. * * Additional information * This function

Signal from Macro Module that all keys have been processed (that it knows about)

Main Periodic Scan This function is called periodically at a constant rate Useful for matrix scanning and anything that requires consistent attention

Reset Keyboard

Reset Keyboard

Get timestamp of Test Domain Timer. \return Current timestamp value. */

USB Input buffer available

Sets the device into firmware reload mode

USB Get Character from input buffer

USB Data Periodic

USB Data Poll

USB Send Character to output buffer

USB Send String to output buffer, null terminated

USB RawIO buffer available

USB RawIO get buffer XXX Must be a 64 byte buffer

USB RawIO send buffer XXX Must be a 64 byte buffer

USB Module Setup

Soft Chip Reset

Add time amount to a given variable Returns 1 if there was an ms rollover

Compares two Time variables -1 if compare is less than base 0 if compare is the same 1 if compare is more than base

Number of ticks since

Increments TransactionBuffer head pointer Returns 1 if successful, 0 if buffer empty and cannot increment

Check if valid head

Check if valid head

Votes on the given key vs. guide, long macros A long macro is defined as a guide with more than 1 combo

Votes on the given key vs. guide, short macros

Handle short trigger DRO state transitions

Evaluate/Update TriggerMacro