* \brief Get supply controller status. * * \param p_supc Pointer to a SUPC instance. * * \return The status of supply controller. */

Read access port register.

Read 8-bit byte from target memory.

Read target memory.

Read debug port register.

SWD Reset

Write 8-bit byte to target memory.

Write target memory.

Write unaligned data to target memory. size is in bytes.

* \brief Initialize flash wait state according to operating frequency. * * \param ul_clk System clock frequency. */

reads the next utf-8 sequence out of a string, updating an index */

* \brief Returns a value to check the end of USB Configuration descriptor * * \return address after the last byte of USB Configuration descriptor *

* \brief Disables an usb device interface (UDI) * This routine call the UDI corresponding to interface number * * \param iface_num Interface nu

* \brief Enables an usb device interface (UDI) * This routine calls the UDI corresponding * to the interface and setting number. * * \param iface_

* \brief Search specific descriptor in global interface descriptor * * \param desc Address of interface descriptor * or pre

Returns list of unread callbacks

TODO Updates the internal tracking @return: True if ready to evaluate/execute

Current us count for CPU Uses both cycle count and systick TODO (HaaTa) - Make it possible to use dynamic F_CPU Possibly using a table of supported fr

Send packet to host XXX Only transfers RAWIO_TX_SIZE on each call (likely 64 bytes) Always returns RAWIO_TX_SIZE

* Returns: 0 when this is was the last transfer, 1 if there is still * more to go. */ Defaults to EP0 for now */

Ignore verification @param: State of result @return: Always True

Process virtual serial port commands

Setup virtual serial port

* \brief Disable the watchdog timer. */

Retrieves the ADCTimedEntry from the head of the ADC buffer

Increments ADCBuffer head pointer Returns 1 if successful, 0 if buffer empty and cannot increment

Increments ADCBuffer tail pointer Returns 1 if successful, 0 if buffer full and cannot increment

Scans the CLILineBuffer for any valid commands

Check user signature When a new firmware is flashed we need to update the user signature This signature is used by the bootloader to determine the fir

See 30.3.1 CHIPID_CIDR | ARCH | Architecture Identifier http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-11100-32-bit%20Cortex-M4-Microcontroller

Attempts to detect chip part revision number using registers only See 30.2 (Table 30-1) for part numbers http://ww1.microchip.com/downloads/en/DeviceD

Called after firmware download has completed, but before reseting and jumping to firmware

Called during each loop of the main bootloader sequence

Called early-on during ResetHandler

Serial Number retrieval

Called during bootloader initialization

Key validation Point to start of key Returns -1 if invalid Returns start-of-data offset if valid (may be unused until next block)

Setup DAP

Called during each loop of the main bootloader sequence

Called early-on during ResetHandler

Called during bootloader initialization

Get id from data stream May be either 16 bits or 32 bits wide

Return width in bytes

Initiate registered call function id - Function id buf_pos - Index in ring buffer irq - Set to 1 if called from an IRQ

Calculate Id width in bytes

Determines max payload with given id width

Modify buffer in place XXX (HaaTa): Does not check tail bounds, responsibility of caller to verify bonuds are correct

Get data payload start of packet

Initiate registered reply function id - Function id buf - Pointer to the ack buffer irq - Set to 1 if called from an IRQ

Process all ADC samples

Clear Display

Signal from parent Scan Module that available current has changed current - mA

Setup

Write to a data register with a0 bit high

PixelBuf lookup (LED_Buffers) - Determines which buffer a channel resides in

Write ISSI page

Detect short or open circuit in Matrix Only works with IS31FL3733

Detect short or open circuit in Matrix - Uses LED Mask to determine which LED channels are working/valid - Detect shorts, used for manufacturing test